This was not due to failure in the authentic VCDS interface or software which is available for download 24/7 on our website. This cracked/pirated software is altered (by the thief) to work with illegal / counterfeit cables (that they sell) and modified the interface in an attempt to preserve the pirated product they sell.
VCDS is short called “VAG-COM Diagnostic System ”,also called VAG-COM.VCDS is primarity used for diagnostic and adjustment for Volkswagen Group vehicle.VCDS will perform most of functions that only performed by expensive official dealers,it is very suitable for DIY user and garage.
VCDS Functions List:
Auto Scan
Control Unit Info
Read Fault Codes
Output Tests
Selective Output Tests
Basic Setting
Clear Fault Codes
Close Controller
Code Module
Code Slave Modules
Measuring Blocks
Advanced Measuring Values
Single Reading
Adaptation
Login/Coding II
View Readiness
Guided Readiness Scripts
Security Access
Support Codes
Generic OBD-II
Freeze-Frame Data
Dual K-Line Support
Digit PINs (VAS only)
Code Database Up to Date
Diagnostics via CAN
Transport Mode
Support for Dual ECUs
Data Logging
HighSpeed DataLogging
Real-Time Graphs
Real-Time Gauges
Graphic TDI Timing Checker
Control Module Finder
Automate Service Reset (SRI)
ECU Mileage Checker
Controller Channel Maps
Wireless Connection via WiFI
Installation List
LT3/Crafter Support
VCDS Support Vehicle Models List:
The following VCDS Compatibility Charts are based on Model and Chassis Type. To find the Chassis Type for your car, look at the 7th and 8th digits of the VIN number. The Chassis type will usually be found in these digits. There are exceptions.
Example (Audi A6):
VIN: WAUZZZ4F36N111022
The 7th and 8th digits are 4F for Audi A6 (4F), the 10th digit is 6 which stands for Model Year (MY) 2006. See the Model information Column for Audi to find the A6 Model. Note that the Chassis Type “4F” is listed under that model. Look horizontally across the VCDS Compatibility Chart until you find the Model Year 2006 and you can determine which interface(s) is required for that Chassis. In this particular case you will see that only the HEX+CAN series interface is compatible.
Please Note: Older VCDS versions may not support all of the model years listed. These charts are intended for the most current version of VCDS (in rare cases even Beta Versions).
Check the VCDS Compatibility Charts to get details
b) hardware type detect program to know what to flash inside.
c) flash interface by usb (interface with genuine firmware , must be connected to 12V)
d) loader to be used with any genuine install kit
e) info.pdf to read how to do stuff
f) projects already made to flash by programmer (tl866 or usbasp)
g) ept and xml files for ft232rl or rq just in case.
LOADER V2.txt
Update 14.08.2017
Loader V2 compatible with RL-RQ-BL-BM interfaces.
Reworked tool for update interface by USB – keeps count of type of hw in eeprom.
New eeprom dumps for each version of hardware
Included in pack Progisp v1.72 and also Mprog 3.5 with templates
Remade projects with new dumps for Progisp and TL866
All versions released until today on any language work even NEZ one ?
UPA VCDS FUSES for HW44 and HW46.zip
VCDS Loader V4.txt
New version with new eeprom, need to rewrite your interface with new usb flasher.
One multilingual eeprom is not possible anymore. Use VAGCOM_EEWriteLang to write eeprom of your choice.
VCDS Computer Requirements:
VCDS requires a computer running Microsoft Windows (the HEX-NET can be used with VCDS-Mobile on other platforms but that use is still in beta testing). A Laptop is most convenient but a desktop PC can also be used. We recommend a PC running Windows 7, 8.1, or 10 with at least 2GB of RAM (single-core Atom-class processors are no longer recommended). Screen resolution of at least 800×600 is recommended.
How to Install VCDS Software:
Double click the icon desktop,wait for installing,as shown:
Wait for progress complete to 100%
Select “Next”
Check “I accept the terms of the License Agreement”
Select “Next”
Select components to install,then select “Next”
Wait for progress complete
Click “Finish”
How to use VCDS:
Run VCDS software,connect VCDS VAG COM to your computer USB interface
Click options
Click Test,show that VCDS VAG COM hardware has been activated
Then click save,you can use VCDS VAG COM to test your car
This article will guide you how to install VAG-COM USB cable on Windows and VCDS software. (This article also applies to later versions of VCDS software)
CAUTION:
There's several versions of VAG-COM sold online. Unfortunately 99% of them are using low-grade hardware chip with additional of cracked VCDS software (sometimes needed an awkward computer date adjustment). If you own this kind of version, know half of it's functions don't work. For that reason we recommend you get the high-quality VAG-COM 2019 cable with original, unlocked and full version of VCDS software from Ross-Tech™ — by clicking here.
STEP 1: Install Ross-Tech VCDS Software
DO NOT plug VAG-COM cable into computer yet.
Uninstall any other VCDS versions, if present on computer. Then delete c:Ross-Tech folder.
Install VCDS software. Make sure to tick ON 'Install 32-bit'. (If option is grayed out, don't worry, continue.)
Leave original installation path of: C:Ross-TechVCDS
When install is complete, do not launch VCDS.
Exit the Installer.
STEP 2: Plug VAG-COM Cable Into Computer
Plug VAGCOM cable into any USB port.
Windows will install drivers automatically.
If driver install fails, skip to Troubleshooting.
STEP 3: Disable Internet & Launch VCDS Software
Golden Rule: Disconnect from WIFI before launching VCDS software.
Read golden rule above?If yes, then...
Launch VCDS software from Start Menu. Or from C:Ross-TechVCDSVCDS.exe
Go to: Options » Test (leave it as USB)
It should show 'Port Status: OK':
Click 'Save'.
STEP 4: Enable license
On main screen, click on button:
Make sure it says:
If it shows instead: Invalid/Unauthorized, then do again:
Go to: Options » Test
It should show 'Port Status: OK' > Save > You're now ready to scan your car!
Troubleshooting:
You are here because when you inserted VAG-COM cable for first time, Windows failed to install drivers properly.
Expand:
SOLUTION 1:
Leave cable connected to computer. Restart computer. It should be fixed now. Go to Step 3.
SOLUTION 2:
VAGCOM cable should be connected to computer.
1) Go to Control Panel.
Windows Vista/7/8/10: Control Panel » System » Device Manager
Windows XP: Control Panel » System » 'Hardware' tab » Device Manager
2) Expand 'Ports (COM & LPT)' or 'Universal Serial Bus Controllers'.
You're looking for a device that has name 'Ross-Tech' in it. It will have a yellow mark next to it like this:
Here's an example: OR it may show as 'Ross-Tech Direct USB Interface'.
3) Right-click on this device with the yellow mark » Update Driver Software.
4) Choose 'Browse Computer for Driver Software'.
5) Browse to: 'C:Ross-TechVCDS'. It should look like this:
6) Click 'Next'. When you get below message, choose 'Install this driver software anyway'.
When driver installation is complete, disconnect cable from computer. Restart computer.
When you're back in Windows, you may connect cable into computer, and go to Step 3.
SOLUTION 3 :
If after SOLUTION 2, cable is still showing a Yellow mark (), then you're likely on Windows 8, 8.1, 10 or above.
In this case, disconnect cable.
And disable driver signature enforcement. Here's how: Windows 8/8.1|Windows 10
When done, go to Step 3.
Notes:
DO NOT update the software to latest version, else it will not work. Only works on current version.
If you bought your VAG-COM cable from us, then registration is not needed. It's already registered/licensed.